Transcript
Introduction to the Tensor
Good afternoon, everyone, and welcome to today’s webinar. Today, we’re gonna be talking about the Tensor. The Tensor is PMI’s plug-in-the-wall power quality recorder. This is really a full-featured PQ recorder that offers source min, max, and average voltage and current, but also waveform capture, harmonic measurements, IEEE flicker recording, CBEMA and ITIC event triggering, a whole slew of power quality recording abilities, all on a 120-volt plug-in receptacle monitor.
Connectivity: Wi-Fi and Cell Modem
The Tensor always has Wi-Fi. It also optionally has an embedded cell modem. With the base Tensor™ with Wi-Fi, you can join it to a Wi-Fi network. For example, if it’s an industrial facility or an area that has Wi-Fi, you can join it to the Wi-Fi network, and then it uses that network to transmit data to the cloud, and you can communicate with it directly.
It also acts as a Wi-Fi hotspot or an access point, so you can join a laptop or a phone to the Tensor’s local network. The Tensor hosts its own little mini website, so you can look at real-time readings right on the Tensor, or that’s also the mechanism for joining it to another network. With the embedded cell modem, it’s even simpler. It has a cell connection directly to PMI’s PQ Canvass system.
Relay Control and Environmental Monitoring
Another feature that the Tensor brings to this type of device is relay control of the receptacle. The plug on the front is actually switchable via commands from the web browser. If you have a load that you want to control that you plug into the Tensor, you can switch that load off and on remotely through PQ Canvass.
Another unique feature about the Tensor is the environmental monitoring. The Tensor is able to not only measure power quality, but also measure temperature, air pressure, and humidity to give you full environmental sensing in addition to standard power quality sensing.
UL Listing, Calibration, and Super Capacitors
The Tensor is UL-listed, and it comes with NIST traceable calibration, so you can be assured of its accuracy and safety.
One of the other things we’ve done across our product line is take away any batteries. Batteries fail. Batteries don’t last forever. The Tensor is one of our products that uses super capacitors for ride-through during an outage instead of batteries. So there’s no battery in the Tensor that can fail down the road. All ride-through ability is through super capacitors to get a longer product life.
Electrical Monitoring Specifications
With the electrical monitoring, the Tensor has two channels for voltage. It’s measuring both hot to neutral and neutral to ground. The neutral prong is the reference, so it’s measuring hot to neutral and also neutral-to-ground voltages. That neutral-to-ground voltage has a 90-volt range; hopefully that voltage is close to zero, but if it’s not, it does have quite a bit of range for that.
For the current, it’s a 15-amp receptacle plug on the back of the Tensor, but the range on the Tensor™ allows for 75 amps RMS, and this gives you enough headroom to measure in-rush current. If you plug in something like a motor that has a high in-rush current, the Tensor will be able to capture that accurately on an RMS basis. So it’s got quite a bit of overrange in terms of current, but this is designed to be used on a 15-amp branch circuit.
With the Tensor, you get two channels of voltage, one channel of current, and these are all sampled at 256 samples per cycle. That’s 65 microseconds per sample, and that’s the same sampling rate as our other power quality recorders. So it’s really a full-blown PQ recorder in a 120-volt receptacle.
Features and ProVision Compatibility
It’s very similar to the Revolution and the Guardian, if you’re familiar with PMI’s other PQ devices. It works with ProVision. The analysis in ProVision, our PC software, is actually the same as the other PMI PQ recorders.
It measures min, max, average current and voltage, waveform capture triggering, very similar to the Seeker and the Guardian. Voltage and current harmonics, both magnitude and phase angle, up to the 51st. IEEE 1453 flicker, CBEMA recording, and also real and reactive power and power factor, and THD, both for voltage and for current.
Embedded Cell Modem and Ease of Deployment
The embedded modem is an LTE Cat one modem. This is designed for a wide coverage range, and this makes it very easy, especially for a muni or a co-op who wants to use this for power quality monitoring in a customer’s home. They can send it to the customer. Maybe they mail it to them. The customer plugs it into the wall in their house, and it’s automatically online. Their customer doesn’t have to do anything. Just plug it in, and it automatically attaches to the network and starts streaming data to PQ Canvass.
You can also use it with ProVision remotely. You can connect to the device through ProVision with its IP address, just like another PQ recorder. But it can also be configured to stream data to the cloud.
Wi-Fi and Security
All Tensor units have Wi-Fi. You can use this as an access point where you can join a laptop or a phone to the Tensor’s little mini network, and it will then launch a web browser with its home page. You can look at real-time readings on the Tensor little mini website or use that to join it to an existing Wi-Fi network, at which point it can use that network to stream back to the cloud.
The Tensor has been through several security testing protocols along with our other PQ devices. It’s secure for utilities. It’s undergone extensive testing, and so has our PQ Canvass cloud-based system.
PQ Canvass Live Demo
I’m gonna jump to PQ Canvass. Here I have PQ Canvass loaded. This is a web browser, web-based application that PMI hosts. The Seeker can work in PQ Canvass, the Guardian, and also the Tensor.
I’m going to click on this Tensor. This is plugged in the wall, and I can look at live data. I can look at, for example, the real-time waveforms. Here is voltage and current in channel one, voltage, neutral-to-ground voltage in channel two. Not much voltage on the ground, and actually not much load plugged into this Tensor at this point.
We can see the voltage, we can look at the harmonics, we can look at the vector diagram. Nothing really exciting on this plug-in-the-wall device. We can look at the real-time readings. Here’s RMS voltage, current, power, THD, and other types of information.
Environmental Readings in PQ Canvass
We can also look at the basic voltage, current, and power environmental readings. For example, here is temperature, humidity, air pressure, and this is all reporting into PQ Canvass. We can zoom in and out, and all data is stored. All the data is collected, streamed up continuously, and the data’s never thrown away. So you can go back in time, really back into forever for these devices.
Here in this location, the spikes in humidity you see are the air conditioner cycling off and on, which causes very small but noticeable changes in humidity and temperature as that changes. We can also look at RMS voltage on a graph with the daily profiles to see what the daily variation is for voltage.
PQ Recordings in PQ Canvass
Then we can dive a bit deeper. If you look at recordings, for example, these are PQ recordings just like you would see in ProVision. I’m gonna click on one of the more recent ones, and this is really ProVision in the cloud. Remember, I’m in a web browser, and we have the same graphs and reports that we have in ProVision, where we have our strip charts, we have waveform captures, we have a significant change event capture.
I’m gonna look at RMS voltage and current. Here there’s not really any load to speak of plugged into the Tensor, so there’s not a lot of current to see, but we have that min, max, and average voltage. We see periodic voltage sags at this location, and these are one cycle mins and one cycle maxes, just like you’d have in ProVision.
We have pulled up a different recording. Every time you initialize it, which you can also do through the cloud, that generates a new recording here in this recording list. I’m gonna look at a previous one, and here’s a waveform capture. I believe this is the Tensor being unplugged from the wall. But it will also trigger on cap bank transients, voltage sags, other types of PQ events. We have all the other standard strip charts. We have flicker, we have power, THD. All the harmonics are also available, just like the other recorders.
Unique Features Summary
Again, this is PQ Canvass, but you can also use it in ProVision, our PC-based application, just like another PQ recorder. So really the unique features of the Tensor are the fact that it has an embedded cell modem, super capacitors, environmental monitoring, receptacle control. I can switch the receptacle on and off here in PQ Canvass with this relay button, and the fact that there’s really unlimited memory.
If the data is streaming to PQ Canvass, then there really is no limit to the recording time or the recording resolution because it’s all stored in the cloud. You can use the Tensor as a standalone PQ recorder, and it has a large amount of onboard memory, but the best way to use it is through PQ Canvass so the data’s in the cloud. That way there’s no data storage limitations.
You can have email and text message alerts when something happens. You can set up thresholds for voltage, for current, for power. Even the environmental sensors can be set up for thresholds, so that you can get email alerts when something happens. So this is a great way to provide complete environmental and power quality monitoring.
You can see the same sort of readings are also available in ProVision. Here we have the ProVision environmental readings and real-time power readings. The same graphs that are also in PQ Canvass are available in ProVision, just like the other PQ recorders that PMI provides.
Wrap-Up and Use Cases
To wrap up, the Tensor is PMI’s plug-in-the-wall PQ recorder. This is UL listed, so it’s perfectly fine to give this to a residential customer and have them plug it in a receptacle to allow you to get behind the meter or to do some spot checks without having to send a crew out or do something that requires more labor to get a PQ recording.
The Tensor is also great for spot checks in a substation. Utilities have used these in substations. You just plug it into a receptacle in the control house, convenience receptacle, and that 120 volts on that receptacle inside the control house pretty much follows the substation bus voltage. So that’s an easy way of getting a quick view of the substation bus voltage without having to install something in the substation and network it. That’s another really good use for the Tensor.
If you have any questions about the Tensor, feel free to give us a call anytime at (800) 296-4120, or send an email to support@powermonitors.com, and we’ll be happy to chat. Thanks everyone for attending. Have a great afternoon.